X10 xcommander and domocitz android#
X10 xcommander and domocitz pro#
X10 xcommander and domocitz code#
X10 xcommander and domocitz Pc#

I’m guessing this could be improved and dimming might also be added, but it will get the temporary job done for me. The physical switch launch an event which toggle the relay and have to send the state of the relay (i.e.

Leave the body field blank and save both your recipes.Ĭross your fingers and flip the simulated switch on ST and the X-10 lights should follow. What is X10 Commander The purpose of this program is simple: to allow control of your X10 devices from your iOS/Android mobile device with the touch of a finger. Select GET as the method and the middle option under content type. Insert the appropriate ON or OFF external URL in the URL field. Then for the actions use the MAKE channel in IFTTT. Both aimed at the appropriate ST Simulated Switch. One trigger using the ST Switched On & the other trigger using ST Switched Off. You can add a device in the setup > devices menu.

X10 xcommander and domocitz Pc#

Go to IFTTT (I used the PC browser verison). The first step we need to do is to create a Dummy Device under which we can list the new LED dimmer channels. Test this by putting URL’s in your browser that use your external IP address.Ĭreate a Simulated Switch in ST for each X10 light. Set up port forwarding on your router to forward incoming URL’s to your PC & port 8086

X10 xcommander and domocitz android#

also has Android and IOS clients that may help with testing.

X10 xcommander and domocitz code#

Replace the E4 with the device’s House & Unit Code & OFF with ON to turn a light on. Notifications/Alerts can be sent to any mobile device. (Replace the IP address with your PC’s IP. Domoticz is a Home Automation System that lets you monitor and configure various devices like: Lights, Switches, various sensors/meters like Temperature, Rain, Wind, UV, Electra, Gas, Water and much more. Once X10 commander is installed, you should be able to turn X-10 devices on & off through a browser using this URL: “E4%20OFF” **A similar program is also available for the MAC at

X10 xcommander and domocitz pro#

Load the following on just about any Windows PC:ĭrivers for the CM15A(ActiveHome PRO SDK) if needed: I’m using this as a interim solution that will allow me to use SmartThings as the single interface for home automation while I take my time changing from X-10 to Z-Wave switches.

This is a bit of a pain and it uses the cloud, but it gets the job done.

This requires no coding other than 2 IFTTT recipes per X-10 device. X10Commander, is very simple, can also use the CM11a & CM17 interfaces and accepts commands in the form of a URL. Any idea to fix would be appreciated.I made a simple SmartThings to X-10 interface using IFTTT, a free program called X10Commander & a CM15a X-10 interface. I also have other python scripts that work well with domoticz, just the playcode.py does not work. Then press on some buttons on the remote, the deamon should report which buttons were clicked: pidomo: nc localhost 1099 05/31 16:19:02 Rx RF. The first step is to connect to the Mochad daemon on port 1099 of the Raspberry Pi, with Netcat> to listen in on the communications with the CM19A. Of course the playcode.py then does not work as expected anymore. I am using a Palm Pad Remote Control HR12A. I tried to put #import broadlink and just leave some print out line in the playcode.py to test, then no error in the domoticz log any more. I find out that the error with Domoticz could lie in the '_ init _.py' which is called by the 'import broadlink' in the playcode.py. sh script runs well in the ssh command line but not in domoticz on/off action switch. It’s a tiny file so it should be near instant. Now the command that moves it over: scp config.json piraspberrypi.local:/.homebridge You will be prompted to type in your Raspberry Pi password, and then the transfer will be complete. I tried to put the command /home/pi/domoticz/scripts/RM-Pro/python-broadlink/playcode.py in a sh script but still the same error. This simply lists out all the folders and files in that directory. 08:07:15.772 Error: Error executing script command (/home/pi/domoticz/scripts/RM-Pro/python-broadlink/playcode.py). 08:07:15.354 Executing script: /home/pi/domoticz/scripts/RM-Pro/python-broadlink/playcode.py You have installed Domoticz MQTT and Virtual Sensor If not already done configure Domoticz MQTT and Virtual Sensor hardware. I still got the same error message in Domoticz log: